DIVISION 8 - DOORS AND WINDOWS SECTION 08320 - SECURITY DOORS CIRCLELOCK SECURITY DOOR PART I - GENERAL 1.01
SECTION INCLUDES A.
This section covers the furnishing and installation of a complete
Automatic Security Door System. Provide
complete system that has been fabricated, assembled, and tested for proper
operation at the factory. It includes curved side walls, canopy, ceiling,
access hatch, door wings, glass, motor drive Systems, and security system
as required for installation. 1.02
RELATED SECTIONS A.
Section 07915 - Sealants, Caulking and Seals B.
Section 08400 - Entrances and Storefronts C.
Section 08710 - Door Hardware D.
Section 08810 - Glass and Glazing E.
Section 09600 - Flooring F.
Section 16123 - Electrical Supply and Termination 1.03
QUALITY ASSURANCE A.
Manufacturer shall be a
company specializing in the supply of automatic security doors with a
minimum of 10 years experience. B.
Manufacturer shall supply a factory-trained supervisor during
installation of the door. 1.04
SUBMITTALS A.
Submit project specific shop drawings, finish samples and Operating
& Maintenance Manuals in accordance with Section (
) B.
Indicate pertinent dimensions, general construction, component
connections and locations, anchorage methods and locations, hardware, and
installation details. 1.05
DELIVERY, STORAGE AND HANDLING A.
Deliver materials to job
site in manufacturer's packaging undamaged, complete with installation
instructions. B.
Store off ground, under cover, protected from weather and
construction activities. 1.06
PROJECTISITE CONDITIONS A.
Security doors install below finished floor. Floor must not be more
than 3/8" out of level at any point within the footprint of the
security door. 1.07
WARRANTY Boon
Edam warranties its products against defects in material and workmanship
for a period of one (1) year from the date of substantial completion. This
warranty excludes glass breakage, normal wear on finishes or damage that
occurs due to abuse, misuse or acts of God. PART II - PRODUCTS 2.01
MANUFACTURER Factory
assembled and tested Circelock Automatic Security Door Model
CL5OO (3'-3") or CL 750 (5'-0") as manufactured by: Boon
Edam, Inc., 4050 South 500 West, Salt Lake City, Utah 84123. (801)
261-8980 Fax: (801) 261-1612 Homepage: www.boonedam.com AUTHORIZED
DISTRIBUTOR: Ontario Door Controls 1350
Matheson Boulevard East Unit 16, Mississauga Ontario, Canada. Phone:
(905) 238 9222 Fax
: (905) 238 9279 e-mail: products@automaticdoorsystems.com
Website: http://www.automaticdoorsystems.com 2.02
DOOR CONSTRUCTION A.
Curved Side Walls and Canopy: Shall be manufactured
from six (6) extruded aluminum posts, six (6) 8" high one-piece
extruded aluminum canopies and four (4) extruded aluminum bottom rails all
with a minimum thickness of 0.125". B.
Door Leafs: Two door leafs manufactured of 1
3/4" thick aluminum extrusions with minimum thickness of 0.125" C.
Ceiling: Shall be fabricated of formed aluminum sheet.
Ceiling must be secured in position and removed only by authorized
personnel. 2.03
EQUIPMENT A.
Drive System: Overhead drive system with two 1/4 HP AC
motors attached to the internal structural framing. The motor shall be
powered by a 208-230 VAC, 3-phase service. The motor shall a Frequency Controller
to provide for the following characteristics: 1.
Adjustment of door speed through a digital setting 2.
Constant regulation of door speed 3.
Password-protected Security over Frequency Control settings B.
Locking Assembly: Locking of the interior door (secured
side) shall be by fail-secure electric deadbolt lock. Locking of the
exterior door (public side) shall be by fail-safe electromagnet. Both
locks to remain locked at all times until unlocked by authorized signal
from the access control device or building/fir/smoke alarm. Loss of power
will unlock the fail-safe locking unit only, to prevent entrapment.
(Option: Both doors can be fail-safe) C.
Controls: Microprocessor-based electronics utilizing a
2000-step Programmable Logic Controller (PLC) with the following
characteristics:
1. RAM & ROM memory
2. Lithium battery
backup
3. Self-diagnostics for
quick detection of problem source
4. Visual display of
problem source 2.04
SECURITY EQUIPMENT A.
Weight Sensor System: Electronic Load Cells installed in a
steel framework under the floor mat of the door and capable of performing
the following functions:
1. Measure the weight on
the floor mat in the door compartment
2.
Determine if the measured weight exceeds the weight of the pre-set
parameters. If the weight is outside of the preset parameters, the door
will immediately stop and the alarm will activate (This feature will
reduce the chance for "piggybacking" or the coupling of more
than one person in a compartment. Software
for Precision Weight Matching will eliminate the chance for
piggybacking.). B.
Actuation: Door actuation by external card reader, biometric
reader, key pad or remote push button. Although tied into the Circelock,
actuation devices are not by Boon Edam. 2.05
SENSOR SYSTEM A.
Sensor Switches: A system of pressure sensitive switches in
front of rotating door wings (optional) and in front of fixed side walls
that will stop the door's rotation immediately upon compression. All
switches must be tied into the programmable logic controller, give a
visual signal when malfunctioning and cause the door to stop rotating
until corrected. System components shall be incorporated as follows: 1.
S.R.D. (Sensor Rail Doorwing): A multi-directional,
closed-contact pressure sensitive switch contained within a black rubber
profile mounted on the edge of each door wing that will immediately stop
the door's movement if compressed. B.
Emergency Egress Doors: The two doors shall be capable of
sliding open to allow for unobstructed egress in cases of emergency. 2.06
HARDWARE/MATERIALS A.
Tempered Glass: All curved glass shall be 1/4" clear
bent tempered safety glass. B.
Laminated Glass (Optional): 7/16" clear curved
laminated safety glass is available as an option. C.
Bullet Resistant Glass (Optional): Bullet resistant glass up
to Level I glass is available as an option. D.
Aluminum Extrusions: Heavy-duty profile aluminum extrusions
with minimum thickness of 0.1 25. E.
Weather Stripping: Genuine horsehair weather stripping on
all required edges of door wings. 2.07
FINISH A.
Enclosure Walls: Anodized aluminum, kynar painted or
powder-coated aluminum, stainless steel or architectural bronze (muntz
metal) clad. B.
Sliding Doors: Anodized aluminum, kynar painted or
powder-coated aluminum, stainless steel or architectural bronze (muntz
metal) clad. C.
Ceiling: Anodized aluminum, kynar painted or powder-coated
aluminum, stainless steel or architectural bronze (muntz metal) clad. PART III - EXECUTION 3.01
INSTALLATION A.
Inspection: Installer must examine the location and advise
the Contractor of any site conditions unacceptable for proper installation
of product. These conditions include but are not limited to the following: 1.
Floor Out of level more than 3/8" at any point within the
footprint of the door 2.
Floor cutout not yet provided. Installation
shall not begin until these unacceptable conditions are rectified. B.
Erection: Install revolving doors in accordance with
manufacturer's printed instructions. Set units level, plumb, and with
uniform hairline joints. Anchor securely into place. Use only
factory-trained installers. C.
Adjustment: Installer shall adjust door, hardware and
sensors for smooth operation and proper performance. D.
Instruction: A factory trained installer shall demonstrate
to the owner's maintenance crew the proper operation of the door and the
necessary service requirements such as lubrication, cleaning, and
inspection of components. E.
Cleaning: Clean metal and glass surfaces carefully after
installation to remove excess caulk, dirt and labels. |