|
DIVISION 10 - PEDESTRIAN CONTROL DEVICES SECTION 10450 - GATES WINGLOCK SECURITY GATES PART I -
GENERAL 1.01
SECTION INCLUDES A.
This section covers the furnishing and installation of a complete
Automatic Security Gate. Provide complete
system that has been fabricated, assembled, and tested for proper
operation at the factory. It includes railings, door wing, glass, motor
drive system and security system as required for installation. 1.02
RELATED SECTIONS A.
Section 0791 5 - Sealants, Caulking and Seals
B. Section
08400 - Entrances and Storefronts C.
Section 08710 - Door Hardware D.
Section 08810 - Glass and Glazing E.
Section 09600 - Flooring F.
Section 16123 - Electrical Supply and Termination 1.03
QUALITY ASSURANCE A.
Manufacturer shall be a company specializing in the supply of
automatic security gates & turnstiles with a minimum of 5 years
experience. B.
Installer shall supply a factory-trained supervisor during
installation of the door. 1.04
SUBMITTALS A.
Submit project specific shop drawings, finish samples and Operating
& Maintenance Manuals in accordance with Section (
). B.
Indicate pertinent dimensions, general construction, component
connections and locations, anchorage methods and locations, hardware, and
installation details. 1.05
DELIVERY, STORAGE AND HANDLING A.
Deliver materials to job site in manufacturer's packaging
undamaged, complete with installation instructions. B.
Store off ground, under cover, protected from weather and
construction activities. 1.06
PROJECT/SITE CONDITIONS A.
Gates install on finished floor. Floor must be level. 1.07
WARRANTY Boon
Edam warranties its products against defects in material and workmanship
for a period of one (1) year from the date of substantial completion. This
warranty excludes glass breakage, normal wear on finishes or damage that
occurs due to abuse, misuse or acts of God. PART
II - PRODUCTS 2.01
MANUFACTURER Factory
assembled and tested Single wing Winglock Automatic Security Gate as
manufactured by: Boon
Edam, Inc., 4050 South 500 West, Salt Lake City, Utah 841 23. (801)
261-8980 Fax: (801) 261-1612
Homepage: www.boonedam.com AUTHORIZED
DISTRIBUTOR: Ontario Door Controls 1350 Matheson Boulevard East Unit 16, Mississauga Ontario, Canada. Phone: (905) 238 9222 Fax : (905) 238 9279 e-mail: products@automaticdoorsystems.com
Website: http://www.automaticdoorsystems.com 2.02
CONSTRUCTION
A. Frame:Shall be manufactured from 4Omm brushed stainless
steel tubes connected to the center column.
B. Door Wing: Door to be manufactured of 1/4" tempered
safety glass. C.
Center Shaft: Steel framework
containing all of the controls. Center shaft is clad with brushed
stainless steel sheet. 2.03
EQUIPMENT A.
Drive System: Electromechanical drive system specially
designed for the Winglock mounted inside the center
column together with all of the controls. The drive system is
bidirectional, allowing two-way traffic
(not simultaneously). In case of power failure, the doorset can be
operated manually. (Requires a 208-230
V, 1 0 A service from below finished floor) B.
Locking Device: Electromagnetic locking device linked
directly to the center shaft, capable of stopping the doorset at any
position. The locking device is activated in the rest position by a card
reader or remote push button. The Tourlock locking device unlocks in the
case of a power failure. C.
Controls: Microprocessor-based electronics utilizing a
800-step Programmable Logic Controller (PLC) with the following
characteristics: 1.
RAM & ROM memory 2.
Lithium battery backup 3.
Self-diagnostics for quick detection of problem source 4.
Visual display of problem source 2.04
SECURITY EQUIPMENT A.
Actuation: Door actuation by external card reader, biometric
reader, key pad or remote push button. Although tied into the Winglock,
actuation devices are not by Boon Edam. 2.05
MATERIALS A.
Tempered Glass: All glass shall be 1/4" clear tempered
safety glass. PART
III - EXECUTION 3.01
INSTALLATION A.
Inspection: Installer must examine the location and advise
the Contractor of any site conditions unacceptable for proper installation
of product. B.
Erection: Install gates in accordance with manufacturer's
printed instructions. Set units level, plumb, and with uniform hairline
joints. Anchor securely into place. Use only factory-trained installers. C.
Adjustment: Installer shall adjust door and hardware for
smooth operation and proper performance. D.
Instruction: A factory trained installer shall demonstrate
to the owner's maintenance crew the proper operation of the door and the
necessary service requirements such as lubrication, cleaning, and
inspection of components. E.
Cleaning: Clean metal and glass surfaces carefully after
installation to remove excess caulk, dirt and labels. |